Troubleshooting Worcester Boiler Error Codes / Symbols: What does the error code mean on my boiler?

Troubleshooting Worcester Boiler Error Codes / Symbols: What does the error code mean on my boiler?

Caution: While error codes on your Worcester boiler can offer insights, they may signify deeper issues. Don’t hesitate to contact us for a FREE, no-obligation quote from our expert engineers for prompt assistance.

Need a new boiler?

Need a new boiler?

What do the error symbols mean on my boiler?

Siphon fill mode. The boiler will run at a low burn for about 15 minutes to fill the condense trap. This happens after the boiler has been turned off, if it hasn’t been used for a day or so, and if the control knob has been turned down and back up. This is perfectly normal – it is a safety feature of the boiler. It will last about 15 minutes, the boiler will then go back to normal. If the boiler does this for more than half an hour, please ring us on 02890 451010

Key Lock (child lock) – the front panel has been locked (New Greenstar 24/28 only)

One key has been pressed

Two keys have been pressed at once

The boiler is operating in maximum mode. This should not last any longer than 15 minutes. Leave the boiler alone for 15 minutes, if the symbol is still showing after 15 minutes, please ring us on 02890 451010 to arrange an appointment.

The boiler is operating within a set range (service function 1A). Please ring us on 02890 451010.

The boiler is operating in minimum mode. This should not last any longer than 15 minutes. Leave the boiler alone for 15 minutes, if the symbol is still showing after 15 minutes, please ring us on 02890 451010 to arrange an appointment.

Air purge mode. The boiler will not fire, but will pulse the pump on and off. This should only happen when the boiler is first switched on after installation, or if a circuit board is changed. It will last about 15 minutes, then the boiler will go back to normal operation. If the boiler does this for more than half an hour, please ring to arrange an appointment on 02890 451010.

‘Save’ function – this is only seen when an adjustment is made in the menus, and then saved. Does not appear in normal operation.

Temperature blocking mode (‘Gradient limitation’). The boiler is programmed to increase its flow temperature by a certain number of degrees per minute. If it exceeds that rate, then this symbol will appear, the burner will stop for two minutes, and will restart afterwards. It means that the flow temperature is increasing too quickly – not really an overheat as such, but it can mean there is a circulation issue. It can also happen on initial installation, especially with the CDi Conventionals. If continues, please ring 02890 451010 to arrange an engineer appointment.

The display will flash between this symbol and the flow temperature. On this model of boiler it means the service is due.

The display will flash between this symbol and the flow temperature. The heating circuit pump is blocked, please ring 02890 451010 to arrange an engineer appointment.
The SE Code is not a fault, it is a function that is displayed when the boiler has run for 2324 hours, which is average for a 12 month period. And therefore is due for a Service. You can book a service online with us here.

 

Below is the fault codes section from the manual for the Greenstar 4000 Combi Boiler, one of the most popular Worcester models. Although the code and description are included, the remedy has been removed since you should only ever use a qualified and competent Gas Safe registered engineer to service your boiler. They’ll have the knowledge to carry out the checks and tests needed to determine that your boiler is working safely, and they’ll be able to make any repairs that are required too. All of our engineers at solv are Gas Safe registered.

Worcester Fault Codes

 

Understanding the error symbols on your Worcester boiler can provide valuable insights into its operation. However, if you encounter any uncertainties or persistent issues, don’t hesitate to reach out to us for expert assistance. Our team of Gas Safe registered engineers is here to ensure your boiler operates safely and efficiently. Contact us today for a FREE, no-obligation quote and prompt service.