Chat
* indicates required fields

Where Is My Stop Tap or Stopcock?

Where Is My Stop Tap or Stopcock?

If a pipe bursts or a major leak develops in your home, knowing how to turn off the water quickly can make a considerable difference to the amount of damage caused.

However, recent research from WaterSafe Register found that 21% of people in Northern Ireland do not know where their internal stop tap is — the highest proportion recorded across the UK.

Your stop tap may also be called a stopcock, stop valve, mains water valve or water shut-off valve. Whatever name you use, it is the main control for the water supply entering your property.

Finding it before an emergency and checking that it still operates could save valuable time, reduce water damage and make it easier for a plumber to carry out repairs.

Is a stop tap the same as a stopcock?

Yes. The terms stop tap and stopcock are generally used to describe the same plumbing fitting: the valve that controls the mains water supply entering your home.

You may also hear it described as:

  • An internal stop valve
  • A mains water valve
  • A mains shut-off valve
  • A water shut-off valve
  • A water isolation valve

“Stop tap” is now the term commonly used by water companies and approved plumbing organisations, while many homeowners and tradespeople still call it a stopcock.

Individual appliances and plumbing fittings may also have smaller isolation valves. These control the water to one particular appliance, tap or section of pipework, whereas the main stop tap or stopcock controls the incoming supply for the property.

When would I need to turn off the water?

Turning off the stop tap stops or substantially reduces the flow of mains water through the property. This is particularly important if you discover:

  • A burst or leaking pipe
  • Water escaping from a plumbing fitting
  • A damaged tap or appliance connection
  • A leak that cannot be immediately contained
  • Water coming through a ceiling or wall

If the source cannot be identified or isolated separately, turning off the main water supply can help limit further damage until a plumber arrives.

Where is my stop tap likely to be?

The location varies between properties, but internal stop taps or stopcocks are commonly found:

  • Under the kitchen sink
  • Inside a kitchen cupboard
  • In a downstairs bathroom or utility room
  • Under the stairs
  • In a garage, cellar or basement
  • Close to where the mains water pipe enters the property

In flats and apartments, the stop tap may be located in a communal service cupboard, utility area or another accessible part of the building. If you rent your home, your landlord or managing agent should be able to tell you where it is.

Stop taps can become hidden behind stored items or alterations made by previous occupants, so it is worth finding yours while everything is working normally.

What does a stop tap or stopcock look like?

A traditional stopcock usually looks similar to a small brass tap, with a T-shaped, cross-shaped or rounded handle that turns several times.

Some properties have a lever-style stop valve instead. With this type, the lever normally sits in line with the pipe when the water is on and across the pipe when the supply is turned off.

You may also have an external stop valve near the boundary of your property, often beneath a small cover. However, the internal stop tap should usually be your first option during a household plumbing emergency.

How do I test my stop tap?

WaterSafe Register recommends checking that your stop tap operates approximately every six months. The changing of the clocks can be a useful reminder.

To test a traditional screw-down stop tap or stopcock:

  1. Turn it slowly clockwise to close it.
  2. Open a cold tap and check that the water flow stops or reduces.
  3. Turn the stop tap anticlockwise to reopen the supply.
  4. Once fully open, turn it back approximately half a turn to help prevent it from seizing.

Lever-style valves should be returned to the fully open position, with the lever in line with the pipe.

Never use excessive force. If the valve is stiff, seized, leaking or will not turn, contact a qualified plumber rather than risk damaging it.

Why should it be checked regularly?

A stop tap may remain untouched for years. Over time, it can become difficult to operate because of corrosion, limescale or internal wear.

Discovering that your stopcock is seized during a burst pipe is far from ideal. Checking it periodically allows you to identify a problem while there is still time to arrange a repair.

Everyone in the household should know where the mains water valve is, particularly anyone who may need to respond to an emergency while you are away. You could also place a small label inside the relevant cupboard to make it easier to find.

What should I do if a pipe bursts?

If it is safe to do so:

  1. Turn off the internal stop tap or stopcock.
  2. Switch off the heating system and any affected electrical supply if water is near electrical fittings—but only if this can be done safely.
  3. Open cold taps to help drain water from the system.
  4. Contain escaping water with towels, buckets or containers where possible.
  5. Contact a qualified plumber.

Do not touch electrical equipment, sockets or switches that are wet or surrounded by water. If there is an immediate electrical danger, keep clear of the affected area and seek emergency assistance.

Need help with your stop tap?

If your stop tap, stopcock or mains water valve is difficult to operate, leaking or inaccessible, it is better to address the problem before an emergency occurs.

solv provides professional plumbing services across Belfast and Northern Ireland, from repairing leaks and replacing faulty valves to helping protect your property against future plumbing problems.

Don’t wait for a leak. Check your stop tap today.